Tom Scribner

Follow
  • Total activity 24
  • Last activity
  • Member since
  • Following 0 users
  • Followed by 0 users
  • Votes 5
  • Subscriptions 9

Activity overview

Latest activity by Tom Scribner

  • Tom Scribner commented,

    1. Community
    2. Troubleshooting
    3. Problem with 1st time program command

    Upon further evaluation, it seems the program statement has an issue with the three variables for programming the nrf52.  The following seem to be required. 1) The statement program requires three ...

  • Tom Scribner created a post,

    PLT Unable to Boot with Scanner

    1. Community
    2. Troubleshooting

    Hi,  We are using a Zebra LS2208 Hand Scanner and the PLT200 is unable to complete booting with the scanner plugged into the USB port.  If I unplug the scanner and power down/up the PLT200 is it ab...

    • Tom Scribner
    • 2 followers
    • 1 comment
    • 0 votes

  • Tom Scribner created a post,

    No Label Print upon Failure

    1. Community
    2. Troubleshooting

    Is there a way to NOT print a label upon a test failure?

    • Tom Scribner
    • 2 followers
    • 1 comment
    • 0 votes

  • Tom Scribner created a post,

    Can't dial error message with BLE gatt connect

    1. Community
    2. Troubleshooting

    When I try to make a connection via ble, I receive the error message "can't dial: connection canceled"   57.062s PROD-02.2 ble gatt connect name:%BCASTNAME% 30 FAIL connect: can't dial: can't di...

    • Tom Scribner
    • 1 follower
    • 0 comments
    • 0 votes

  • Tom Scribner created a post,

    Problem with 1st time program command

    1. Community
    2. Troubleshooting

    I'm noticing a situation where after a reset, my program statement fails.  If after the failure I press the start again, the program statement will succeed.  My script is below. NOTE: The 1st progr...

    • Tom Scribner
    • 1 follower
    • 1 comment
    • 0 votes

  • Tom Scribner created a post,

    Zebra Label Printer Setup

    1. Community
    2. Troubleshooting

    Are there instructions on how to install a Zebra Label Printer.  I have a GX430t printer and have connected the printer up to the USB port, however, my label command does not print.  I have created...

    • Tom Scribner
    • 1 follower
    • 0 comments
    • 0 votes

  • Tom Scribner created a post,

    Program DUT without Erase

    Completed
    1. Community
    2. Feature Requests

    During your program statement, an automatic erase occur's for the DUT's ram contents.  There are situations where the contents of NVRAM should not be erased.  It would be nice to have a flag for th...

    • Tom Scribner
    • 1 follower
    • 0 comments
    • 2 votes

  • Tom Scribner created a post,

    Expecting UART communications

    1. Community
    2. Troubleshooting

    I am working on this script with interaction with my firmware and apparently, it's not working as I expect it to.  Basically, I have a bare-bones firmware module that I initiate manufacturing tests...

    • Tom Scribner
    • 1 follower
    • 0 comments
    • 0 votes

  • Tom Scribner created a post,

    Remote Execution

    1. Community
    2. Feature Requests

    Have the ability to remotely start a test script

    • Tom Scribner
    • 1 follower
    • 0 comments
    • 1 vote

  • Tom Scribner commented,

    1. Community
    2. Feature Requests
    3. Remote Debugging

    Along with this remote debugging feature, would be the ability to kick off a script remotely.